Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C

Titanium 6Al4V Titanium Alloys Mechanical Chemical Physical Properties Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Titanium 6Al4V Grades Titanium Alloys Mechanical Chemical Physical Properties Ti 6-2-4-2 Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C Ti 15-3-3-3 Titanium 6Al4V IMI 685 Titanium Alloys Mechanical Chemical Physical Properties IMI 829 Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C CP Grade 1 CP Grade 12 CP Grade 2 CP Grade 3 CP Grade 4 CP Grade 7 / 11 / 16 Grade 5 / ELI / 23 Grade 9 / 18 Grade 19 / 20 titanioum , titan, titane, titanio, tianium, titaium, titanim, titaniom, titanium, titanum, titnium, ttanium, t1tan1um, titanium, titamium, titanimu, titanuim, titainum, titnaium, tiatnium, ttianium, ittanium, titaniu, titanim, titanum, titaium, titnium, tianium, ttanium, itanium, titaniom

- about Ti - Introduction Ind. Specification Medical Specification Applications Characteristics Classification Markets Corrosion Engineering Fabrication   - Ti Grades - Introduction Ti 6-2-4-2 Ti 15-3-3-3 Ti 13Nb-13Zr IMI 685 IMI 829 SMA CP Grade 1 CP Grade 12 CP Grade 2 CP Grade 3 CP Grade 4 CP Grade 7 / 11 / 16 6Al4V Grade 5 / 23 6Al7Nb Alloy Grade 9 / 18 Alloy Grade 19 / 20   - Ti Products - Introduction Fine Wire - Cable Foil Sheet / Plate Titanium Targets Tube Oilfield Tubes

News 7. 7. 10:
Surplus Titanium Sheet Grade 2 ASTM F 67

» Titanium Grade 12

Used in applications whereas good corrosion resistance at high temperature is requested. Unalloyed titanium offering optimum ductility and cold formability with useful strength, high-impact toughness, and excellent weldability. Highly corrosion-resistant in oxidizing and mildly reducing environments, including chlorides.

» Current Coils in Special offer!

20th October 2006

all sizes in [mm] - THK x Width x coil
0.71x110	0.71x105
0.71x69.8	0.71x511
0.71x90
0.8x100
0.84x58.9	0.81x75
0.889x158.7	0.889x101.6
0.889x895	0.889x69.8
0.889x79	0.889x58.9
0.889x99	0.889x59.1
0.96x361.9	0.99x198

Composition Physical Data Mechanical Data Fabrication Information

» Composition

C	< 0.08 %
Fe	< 0.3 %
N2	< 0.03 %
O2	< 0.25 %
H2	< 0.015 %
Ni	0.6 - 0.9 %
Mo	0.2 - 0.4 %
Ti =	Rem

» Physical Data

	Minimum	Typical
Density g/cm3 (lb/cu.in)		4.51(0.162)
Melting Range °C+/-15°C (°F)		1670(3038)
Specific Heat J/g/°C		0.54
Volume Electrical Resistivity µohm (µohm.in)		56(22)
Thermal Conductivity W/mK(Btu/ft h°F)	22(153)
*Mean Thermal Exp. Coeff. 0-100 °C/°C		8.6 x 10 -6
*Mean Thermal Exp. Coeff. 0-300 °C/°C		9.2 x 10 -6
Beta Transus °C+/-15°C(°F)		888 (1630)

» Mechanical Data

	Minimum	Typical
Tensile Strength MPa(ksi)	483 (70)	> 620 (90)
0.2% Proof Stress MPa(ksi)	345 (50)	> 430 (62)
Elongation over 2 Inches %	18	> 20
Reduction in Area %	25
Elastic Modulus GPa(Msi)	103 - 107 (15)
Hardness Brn	180-235
Short Term Creep, 1.0% Strain (1000h @ 250°C) MPa (ksi)		221 (32)
Stress Rupture (1000h @ 250°C) MPa		297 (43)

» Fabrication Information

Weldability	Excellent
Annealing	705°C (1300°F), 2 hr, AC
Stress Relief Annealing	540-595°C (1000-1100°F), 15-30 min.

Titanium Tantalum Molybdenum Niobium Zirconium Tungsten
Phone: +41 (0)444 6353 82 Skype: titanexch
© 1994-2010 Titanex GmbH Switzerland powered by euroteam.ch

Titanium 6Al4V

Titanium Alloys Mechanical Chemical Physical Properties

Titanium Grades 1 2 3 4 5 7 9 11 12 19 Beta C

Titanium 6Al4V